Call Us Today! 86-15990205383, 86-574-87562591

Radial Multipole Flow Sensor Rotor Magnets

/Radial Multipole Flow Sensor Rotor Magnets
  • Radial Multipole Flow Sensor Rotor Magnets

Radial Multipole Flow Sensor Rotor Magnets, Water Flow Sensor Magnets, Water Flowmeter Magnet, Injection Molded Ferrite Magnetic Assemblies, Bonded Rare Earth magnet materials such as NdFeB, SmCo and SmFeN can molded as well as Ferrite material, Injection Molded Permanent Magnets, Isotropic and Anisotropic Permanent Plastic ferrite bonded magnet, Magnetic Assembly China Supplier

Radial Multipole Flow Sensor Rotor Magnets Part No. HSIMM-06
Material: injection-molded ferrite
Number of magnetizing poles: radial multipole 8 poles
Purpose: flow sensor, water flowmete

The product name is water flowmeter magnet, flow sensor magnet, flow sensor rotor. The magnetization mode is radial multipole. If you are interested in this product, please contact by email.

Water Flow Sensor Magnets
Water flow sensor is a type of water flow induction instrument which output pulse, current or voltage signal through induction to the water flow. The output of the signal has a certain linearly proportional to the water flow. Thus can be served to the management of water control and flow calculation depend on the relevant conversation formula and comparison curve. Actually, as a core component of water flow sensor, water flow sensor magnets have long been a typical application of injection molded ferrite magnet.

Working Principle of Water Flow Sensor
Water flow sensor is mainly composed of copper valve body, water flow rotor assembly, steady flow system and hall component. Water flow sensor is usually installed on the inlet of the heater to measure influent flow, and magnetic rotor assembly rotates when water flow through it. Hall component output and feedback corresponding pulse signal to controller, then controller adjust current of proportional valve and hence gas usage according to the flow rate.

Water flow rotor assembly mainly consists of turbine switch housing, magnetic rotor, and brake ring. Water flow sensor magnets are essentially a hall effect sensor magnet. Hall component will conduct when different magnetic poles toward it, then cut off once away.

Injection Magnet Plastic Magnet What is Injection Moulding

Magnet material can be directly molded into, onto, or against other assembly components eliminating subsequent assembly steps. This is called insert injection molding.

Injection molded magnets are available by using ferrite, neodymium-iron-boron, or blends of magnetic materials to achieve an extensive range of properties. Binder materials include Nylon 6 and 12, PPS, and Polyamide. The binders and magnetic alloys are capable of a wide range of working temperatures from below -40°C to above 180°C. The Injection molding process allows the ability to produce very intricately shaped magnets with extremely tight tolerances and a wide variety of physical and magnetic characteristics. The finished parts can be either very simple or complex in geometry.

The properties of injection molded magnets vary greatly, depending on the type of magnetic material and binder utilized. GME has both Neodymium and Hard Ferrite injection molding capability, and it is also possible to utilize a blend of different magnetic material to produce the desired properties. Several types of binder can be employed depending on the application, and we offer a variety of nylon and PPS grades to suit the specific needs of our customers.

Benefits of Injection-Molded Ferrite:
Ideal for large production runs
May be molded into complex shapes
May be molded onto shafts or to be attached to other components
Tolerances as tight as 0.01 mm
Impact and chemical resistance
Energy products to 16 kj/m3
Isotropic and Anisotropic grades
Neodymium hybrids can increase performances
Co-injected assemblies

Plastic Magnetic Rotor for Automobile Water Pump Motor
Project of Injection Magnets
In most motor control systems, several sensors are used to provide feedback information on the motor. These sensors are used in the control loop and to improve the reliability by detecting fault conditions that may damage the motor. Automobile Water Pump Rotor Magnet Injection Moulding
Compression Bonded:
Higher Magnetic Strength due to higher magnetic particle density. Injection Moulding Water Flowmeter Magnet
Epoxy Binder / Resistant to normal industrial solvents and automotive fluids
Epoxy Coat after manufacturing to prevent oxidation
Temperature Range -40c ~165c
“Tight” tolerances off tool. Water Flow Sensor Magnets
Good mechanical strength Plastic Magnetic Rotor for Automobile Water Pump Motor
Typical Bonded Magnet Applications:
Sensors
Brushless DC Motors
Household Appliances
Compressor
General Bonded Magnet Applications:
Materials are isotropic and can be magnetized in any direction
Wide range of existing tool sizes are available in rings, discs and rectangles
Exsisting Multipole magnetizing fixtures for quick prototyping
Easily machined
Existing Multipole rings simplify assembly verse arc sepments

If you have any interest or inquiries for Neodymium(NdFeB) magnet, you are welcomed to inquire here. We are sure you will be satisfied with our price and service.

More
  • Customized is Available
  • Affordable price
  • Quality guaranteed
  • T/T or L/C accepted
  • Other payment accepted
  • Fast shipping, Worldwide delivery
  • 24-Hours excellent customer service
  • Offer free magnetic solution
  • Bulk discounts for larger orders

Product Range

Imperial
Metrics
error: Content is protected !!