Call Us Today! 86-15990205383, 86-574-87562591|info@hsmagnets.com

PML-15 3300LBs 1500KG Magnetic Lifter

/PML-15 3300LBs 1500KG Magnetic Lifter
  • PML-15 3300LBs 1500KG Magnetic Lifter

PML-15 3300LBs 1500KG Magnetic Lifter, Heavy Duty Crane Hoist Lifting Magnet, Permanent Magnetic Plate Lifter, Metal Lifting Magnet with Release, Steel Permanent Lift Magnets, Used in Factory Shop Crane for Lifting Plate Steel, Steel Board, Handling Permanent Magnet Lifter China Supplier

PML-15 3300LBs 1500KG Magnetic Lifter Specifications
Color: Yellow
Product: Magnetic lifter
Model: 1500KG
Maximum weight capacity: 1500kg (3300 lb)
Steel plate thickness: >5MM (the thicker the steel plate, the stronger the suction)
Operating temperature: <=80
Magnetic Lifter MAX Weight: 3300 LB.
The Magnetic Lifter is made with super strong neodymium magnets.
Easy to Use Handle to Switch Magnet Force ON or OFF.
Large U-loop shackle hook allows easy attachment of slings.
The magnetic lifter is used for lifting Steel Sheet, Block, Rod and other Magnetic Material.

PML-15 lifting magnets Features:
Easy use: handle with on/off control – attach or detach material.
V slot of bottom lifting face – lift round and flat materialLow residual magnetism for rapid handling
Large U-loop shackle hook allows easy attachment of slingsNotes:
1. Maximum Weight Capacity: 3300 lbs for steel plate, 1650 lbs for round steel
2. Max pull off Force: 9900 lbs
3. V design on the bottom, easier to lift up the round steel.
4. Working temperature: -104 to 176 ℉ (-40°C to 80°C).
5. The magnetic lifter is safe and reliable, small and compact, easy to operate.
6. Turn left to open suction, turn right to close suction.

magnetic lifters are mainly used in shipyards, structural parts factories, warehouses, workshops, freight yards, etc. It can be used with various lifting equipment in the suction special plate massive ferromagnetic materials or workpieces, also can be suitable for suction steel plate, casting Ingots and section steel, and also can be used to suck and transport scrap steel and broken iron, which can be used in a single unit, or multiple units can be used to suck and transport large and long ferromagnetic materials. It used by easy operation, strong suction force, safe and reliable, etc. It is already used in widely on factory, warehouse transportation and so on to save more time and labor productivity.

Question: If I use this on 1/4″ plate steel, how far will the magnetic field extend beyond the plate? Will it lift material under the plate, too?
Answer: If you place some cardboard between the sheets it won’t lift the pcs. under the top pc. but they’re pretty strong magnets, I’ve lifted a pc. of 3/8″ x 48″ x 96″ with 2 of them.

Question: how well will this work for lifting 1/8″x4’x8′ sheet of steel for plasma table? sheets weigh 200lbs. each
Answer: As inexpensive as these were I bought 2 and use a 2×2 1/4″ tube to lift. if the sheet flexes the magnet can loose contact and the steel will fall. I lift 5×10 1/2″ steel and it does fine. Look on youtube for ideas. it works great.

Question: Would the on/off switch still be useful say after it was submerged underwater?
Answer: This magnet is not electronic, it is just mechanical. The on/off switch is just a lever that will work underwater. I don’t think the magnet is made for underwater use, though. PML-15 Heavy Duty Crane Hoist Lifting Magnet 1500KG

Question: could this be used to lift a 500lb table saw
Answer: If you did it right, yes. At least two things would be very important. 1)You would have to put the lifter so it was clamping to the table itself, you need all that metal thickness to develop the full lift capacity of the magnet. And 2) you would have put the lifter on the table in the location so that it was vertically above the center of gravity of the saw. This might sound tricky, but isn’t that hard. Start with the lifter in the center of the table and just lift an inch or so. If the table tilts, put the saw back down and move the lifter a small amount in the “downward” direction of the tilt. Repeat the process as many times as necessary until the table doesn’t tilt in the small lift, and you should be good to go.

Question: Where can I get replacement parts? I need a replacement handle
Answer: This magnet comes from China. No replacement parts are available.

Question: looking at the picture does this lift or it just attaches and the lift is supplied by a lift attached to the top loop?
Answer: This is just a magnet. You will need some type of hoist to pick up your item. You will set the magnet on the item, pull the lever and it will engage the magnet. You can then pick up your load with the hoist.

Question: Where can you purchase repair parts?
Answer: No repair parts available. Magnet come from China. Not rated to ASME standard

Question: If one of these works to lift 200 lbs, will two work together to lift 400 lbs?
Answer: Absolutely

More
  • Customized is Available
  • Affordable price
  • Quality guaranteed
  • T/T or L/C accepted
  • Other payment accepted
  • Fast shipping, Worldwide delivery
  • 24-Hours excellent customer service
  • Offer free magnetic solution
  • Bulk discounts for larger orders

Product Range

Imperial
manual-permanent-lifting-magnet-c-series-drawing

manual-permanent-lifting-magnet-c-series-drawing

 

660LBS 880LBS 1320LBS 2200LBS 3300LBS
Material Magnet Metal Magnet Metal Magnet Metal Magnet Metal Magnet Metal
Operating Temperature < = 80℃ < = 80℃ < = 80℃ < = 80℃ < = 80℃
Steel Plate Thickness >=5MM >=5MM >=5MM >=5MM >=5MM
Color Yellow Yellow Yellow Yellow Yellow
Metrics