Magnetic Pull Force Explained

Magnetic Pull Force Explained – Breakaway force, holding force, fixturing force – “How can all of these represent the same measurement?” a younger engineer recently inquired. Engineers and non-engineers alike can be puzzled trying to understand some of the commonly used – but potentially misinterpreted – terms related to the concept of a magnet’s pull force.

Magnetic Pull Force – These phrases are often used to represent “strength” when writing magnetic specifications. They also may be mentioned when anticipating the work required of a magnet within an application. To add to the potential confusion, the maximum holding force, or how much tensile force is exerted by any magnet, is often shown in the neodymium pull force calculator – are based on theoretical calculations of flux density.

pull-force-testing-hsmag

pull-force-testing-hsmag

One assumption, which may or may not be accurate, is that there is no air gap, or separation between magnet and work piece. Another important “real world” factor that differentiates breakaway force from a required safety consideration is the environment in which the magnet will be used.

Derating, or a reduction in the stated (breakaway) force value of a magnet, may be required depending upon the industry to help avoid safety hazards associated with their use. A “below the hook” application would derate (or reduce the stated force) by a factor of three. Derating (also sometimes written as de-rating) provides an established way to over-engineer reducing safety hazards. An example to help illustrate an application associated with under the hook magnets is a steel plate lifting station on a manufacturing plant floor.

Pull Force Testing

People, plant, equipment, and services in the area of operation could be at risk from being struck by material which becomes detached from the magnet if it was lifting AT THE TRUE STATED MAXIMUM with this derating value being applied.

There is no simple way to calculate the breakaway force if the magnet is not in direct contact. Virtual prototyping of magnets allows us to help customers save time and money. This is where a $30,000 modeling software comes into play.

Within the Public Domain there are several programs available for measurement and modeling of Finite Element Method Magnetics (FEMM). One such software package – MagNet 2D/3D – is a powerful simulation software which engineers and scientists worldwide use for the design of motors, sensors, transformers, actuators, solenoids, or any component with permanent magnets or coils. Using this software allows engineers to virtually prototype simple to complex electromagnetic and electromechanical devices.

As mentioned earlier, engineers may not have taken into account air gap. If the magnet is not going to touch the workpiece due to, for instance, scale built up on steel plates, or a physical distance between workpiece and magnet, the air gap becomes very important in calculating the ACTUAL requirements of the magnet under its specific working conditions.

Often, Magnetic Pull Force – a holding magnetic application comes into our application engineers in which a defined pull-force has been specified. The true engineering phase is identifying the required (and optimally priced) magnet to use to achieve the desired attractive force.

Typically, in many applications, there will be a set of constraints: “only so much room for the magnet,” etc. These size dimensions, along with the actual proximity of workpiece to magnet in turn must be factored in to calculate the breakaway value. This can necessitate investigating alternate grades of magnet to complete the specification. For example, using a bigger magnet that is grade 35, or using a smaller magnet that is grade 45.

Magnetic pull force measurement and specification can be complicated – if you need help engineering the solution, we are available to provide magnetic design assistance. Our powerful simulation software helps us assist engineers worldwide to specify the magnets used in myriad applications. Contact us info@hsmagnets.com today to see if we can help you design your next magnetic application.

magnetic-door-hinges-ndfeb-with-rubberized-based

Magnetic Door Hinges NdFeB

Magnetic Door Hinges NdFeB with rubberized based, rubberized bumper, black NdFeb, Magnetic Hinges NdFeb with rubber based, buffer rubber Magnetic Door Hinges – Magnetic door stop with rubberized bumper. Holds doors and flaps open. Good attenuation through membranous and rubberized magnetic system. Easy fixation with screws. Santoprene Rubber coating, Neodymium Magnets (NdFeB) inside for maximum […]

rubber-coated-magnet-system-with-bore-and-counterbore

Rubber Coated Magnet System with bore and counterbore

Rubber Coated Magnetic System with bore and counterbore, Hard Ferrite or NdFeB Magnet assembly with rubber coat, bore and counterbore / countersunk, Rubber coated pot magnets Rubber Coated Magnet System – These systems are used especially on delicate surfaces. Due to the rubber coating occurs neither scratches nor discoloration. Moreover the slip resistance is improved […]

magnetic-system-with-plastic-coating

Black Plastic Coating Magnetic System

Black Plastic Coating Magnetic System Magnetic System with Plastic Coating, Rubber Coated Neodymium Magnet System, Backpack Magnets in very strong execution, Plastic Covered NdFeB Magnet System Assembly Black Plastic Coating Magnetic System Feature: Material: Neodymium-iron-boron (NdFeB) The magnet systems are equipped with 6 high-power magnets and are well suited for positioning and holding of tank bags […]

rubber-covered-magnetic-systems-for-cable-mounting

Rubber Covered Magnetic Systems for Cable Mounting

Rubber Covered Magnetic Systems for Cable Mounting, Neodtmium magnet system  Ø 22 mm – 43 mm gummed cable mounting /cable fixation, Rubber Coated Magnet assembly NdFeB for Cable Mounting Rubber Covered Magnetic Systems Feature: Model: Magnet system / Cable holder Material: NdFeB (alloy of neodymium-iron-boron) Diameter:  Ø 22 mm – 43 mm Coating: rubber plastic […]

through-hole-magnetic-mounting-pad-rubber-coated

Through Hole Magnetic Mounting Pad MagPad

Through Hole Magnetic Mounting Pad Rubber Coated, Rubber Covered Magnetic Pad with 2 Holes, Magnetic Pads, MagPad, Magnetic Mounting Pad, Rubber Coated Through Hole Magnetic Pads Magnetic Mounting Pad with through hole has one large rectangular bar magnet on its base. This magnet has only one magnetic face, magnetised in the form of a multi-pole […]

magnetic-mounting-pad-with-thread-stud

Rubber Coated Magnetic Pads with thread stud

Rubber Coated Magnetic Pads with thread stud, Magnetic Pads, MagPads, Extra Strong Magpad Magnet with Rubber coated, Magnetic Mounting Pads,Threaded stud magnetic mounting pads Magnetic Pads (commonly known as ‘MagPads’) are used for securing objects to magnetic surfaces. The pad comes with an thread stud with locking nut which is ready to fix. They are […]