What magnetic base accessories are available?
Magnetic base accessories – There are many accessories available for magnetic bases. Some may be included with a base unit, while others may have to be purchased separately in order to tailor your set-up to the job required.
Magnetic base with the most commonly included accessories
The accessories which are most commonly included with a magnetic base are the supporting post, rod/arm, swivel snug or 3 point clamp, and snug. This is due to these accessories being the most frequently required for use with a magnetic base, however, they are not essential for all applications.
Snug attaches to the supporting post and the rod passes through it
A snug attachment fixes to the supporting post and the rod passes through it. The knurled knob is then used to tighten the snug in place.
Dial test indicator snug
Dial test indicator snug is designed specifically to hold dial test indicators
This snug fits onto the rod and is designed for use with the dial test indicator.
Universal snug, allows for stems and rods of different diameters to be used.
This type of snug allows for items of different diameters to be used with the magnetic base, such as different size holding rods/arms and dial indicators, as it has a variety of sizes for fitting.
Swivel post snug
Swivel post snug allows for 360 degree movement.
Allows the user to set the rod when attached to the post in any vertical direction and allowing for 360 degree movement and setting.
Split bushing fits around the stem of the dial indicator.
The bush is fitted around the stem of any item being held by the snug if it’s too small in diameter for a tight fit. The split in the bush allows it to be squeezed tighter together to fit different size diameters.
Holding rod is an extension off the supporting post.
This attachment is an extension of the supporting post used for attaching devices and positioning them as required.
3 point clamp
3 point clamps are used to attach holding rods/arms to the support post of a magnetic base
The 3 point clamp serves the same purpose as the swivel post snug, in that it is used to attach a holding rod/arm to the support post.
Articulating arm attachment for magnetic bases
Articulating arms can be used as a replacement for the support post, holding rod and swivel post snug or 3 point clamp. They have articulating joints at either end with a threaded hole that can be used to attach other accessories that are fitted with a corresponding screw attachment.
Fine adjustment attachments
The term FAT and FAB are used to refer to fine adjustment at top and fine adjustment at bottom when referring to magnetic base accessories, not what you usually thick of when you hear FAT or FAB.
Fine adjustment attachments come in two forms; fine adjustment at bottom (FAB) and fine adjustment at top (FAT). Fine adjustment attachments improve accuracy and are required for precision work such as when taking measurements with a dial indicator.
Fine adjustment attachment makes small adjustments to the setup
FAB attachments are used on the magnetic base to make fine adjustments to the set-up of the supporting post when using a dial indicator. They are attached to the magnetic base via a screw, the supporting post is then screwed to the FAB attachment. The FAB attachment is essentially a looped spring made of steel that can be separated or compressed via a hand screw at its end in order to provide small vertical adjustments to the supporting post.
FAT adjustment can either be built into the rod/arm, or with some rod/arm designs that have a threaded hole at the end for attachments, they can be a separate attachment.
Fine adjustment section built into the rod, for making fine
Built-in fine adjustment
This attachment is built into the rod, and is most commonly seen sold with a magnetic base unit. It allows the user to make small alterations to the set-up to ensure accuracy. The screw makes the fine adjustment and the looped piece of steel connects the two sections of rod.
FAT fine adjustment swivel clamp
Fine adjustment swivel clamp
This type of FAT attachment is designed to screw into the end of a holding rod/arm. The clamp has a small coiled spring inside that is compressed or stretched as the adjusting screw is turned in order to provide the fine adjustment.
Clamp that attaches to the holding rod/arm on a magnetic base by a threaded screw
Clamps usually attach to the holding rod/arm by a threaded screw that screws into the end of the holding rod/arm.
Clamp being used with a magnetic base to hold a splash back guard in place
Clamps can be used to hold many item such as a torch or splash back guard for coolant in machining operations.
Camera mount for use with magnetic bases
Camera mounts attach to the holding rod/arm and have a screw that is used to fix a camera or video camera to them.
Magnetic base accessories
Magnetic Vacuum Base Indicators, Vacuum Magnetic Universal Indicator Base, Magnetic Base Holder Stand, Powerful Magnetic Vacuum Stand Indicator Holder for Dial Gauge Test Indicator Tool China Supplier Magnetic Vacuum Base Indicators Features: Part No.: HSTDH / HSTDE-CC For all kinds of measuring on granite plates or other non-magnetic smooth surfaces Powerful vacuum base holder Fine […]
Magnetic Universal Indicator Base, Rectangle Universal Magnetic Base Holder Stand, Powerful Universal Magnetic Rectangular Stand Indicator Holder, Universal Flexible Magnetic Base Holder Stand for Dial Gauge Test Indicator Tool China Supplier Magnetic Universal Indicator Base Features: Part No.: HSMF-CE / HSMF-CZ / HSMV-STS / HSMV-DCZ Fine adjustment Base with T-groove Many models to choose from […]
Mini Universal Magnetic Base Holder Stand, Powerful Mini Universal Magnetic Stand Indicator Holder, Universal Flexible Magnetic Base Holder Stand for Dial Gauge Test Indicator Tool China Supplier Mini Universal Magnetic Base Holder Stand Features: Part No.: HSMF-CE / HSMF-CZ / HSMV-STS / HSMV-DCZ Smaller than other types of magnetic bases Has On/Off switch and adjustment […]